Minicom Advanced Systems Smart 4 Guia do Utilizador Página 19
- Página / 92
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
2.4.2
Replacing the Bracket
The
rails in your hardware kit come assembled with s
are appropriate for a rack depth of
your needs, proceed to connect the SmartRack 116 IP to the rack (see Section
If you require a rack depth of
longer brackets, as described in the following procedure.
The illustrations
in the following procedure show
the SmartRack 116 IP. The connections are the same for the other side..
To replace the bracket:
1.
Loosen the seven screws
Figure
2.
Remove the six screws
Figure
3.
Remove the rear bracket
Figure
4.
Insert the long bracket into the rail
Tighten at least 2~3 screws along the length
Rack
Mounting SmartRack 116 IP
Replacing the Bracket
rails in your hardware kit come assembled with s
horter brackets. These brackets
are appropriate for a rack depth of
504 ~ 614 mm
. If this rack depth is suitable for
your needs, proceed to connect the SmartRack 116 IP to the rack (see Section
If you require a rack depth of
905 ~ 990 mm
, replace the shorter brackets with
longer brackets, as described in the following procedure.
in the following procedure show
the connections to one side of
the SmartRack 116 IP. The connections are the same for the other side..
Loosen the seven screws
.
Figure
11 – Loosening the Seven Screws
Remove the six screws
(from the bottom and top edges).
Figure
12 – Removing the Six Screws
Remove the rear bracket
.
Figure
13 – Removing the Rear Bracket
Insert the long bracket into the rail
, and
then adjust the bracket to fit your cabinet.
Tighten at least 2~3 screws along the length
that you need.
Installation
Mounting SmartRack 116 IP
User Guide | 19
horter brackets. These brackets
. If this rack depth is suitable for
your needs, proceed to connect the SmartRack 116 IP to the rack (see Section
2.4.3).
, replace the shorter brackets with
the connections to one side of
the SmartRack 116 IP. The connections are the same for the other side..
then adjust the bracket to fit your cabinet.
- SmartRack 116 IP 1
- User Guide 1
- Legal Notice 2
- About this Document 3
- Style Conventions 4
- Table of Contents 5
- User Guide 7
- Table of Figures 10
- User Guide 11
- 1 Introduction 12
- 1.2 Terminology 13
- 1.3 Compatibility 13
- 1.5 Technical Precautions 13
- 1.7 Trademarks 14
- 1.8 WEEE Compliance 14
- 1.6 Safety 14
- 2 Installation 15
- Installation 16
- System Components 16
- 16 16
- The SmartRack 116 IP Unit 17
- Pre-Installation Guidelines 18
- 18 18
- Replacing the Bracket 19
- Connecting 20
- User Guide 21
- 22 22
- 2.5 Connecting the System 23
- 2.6 Connecting to the Servers 23
- Connecting a RICC/ROC PS/2 24
- Connecting a RICC 25
- /ROC USB 25
- Connecting a RICC SUN 26
- User Guide 27
- 3 Configuring the Network 28
- Interface 29
- Configuring the Network 30
- 30 30
- User Guide 31
- 32 32
- 3.3.2 Configuring 33
- Adding a User 34
- Configuring User Settings 35
- User Guide 35
- Deleting User(s) 36
- Blocking a User 36
- Editing User 36
- Information 36
- Configuring the KVM Switch 37
- 38 38
- Installing 40
- Upgrading Firmware 40
- User Guide 41
- 3.9 Reloading a 42
- 44 44
- Conducting 45
- Conducting a Remote Session 46
- Starting a Remote Session 46
- 46 46
- 4.2 Sharing a Remote Session 47
- Exclusive 48
- Full Screen Mode 49
- Verifying 50
- 50 50
- Adjusting the Video 52
- Manually 53
- Adjusting Video Settings 53
- Managing Keyboard Sequences 54
- User Guide 55
- Recording a New Custom Key 56
- Editing a Key Sequence 56
- Synchronizing Mouse Pointers 57
- 58 58
- The USB Option 59
- Aligning the M 60
- Pointers 60
- Calibrating Mouse 61
- 5 Troubleshooting – Safe Mode 62
- Restoring Factory Defaults 63
- Restoring the Device Firmware 64
- Figure 73 – Upgrade Succeeded 65
- Operating 66
- Using the Keyboard Hotkeys 66
- 66 66
- 6.2.3 Configuring t 67
- Configuring Security Settings 69
- Operating the SmartR 70
- Using the OSD 70
- 70 70
- Configuring the Port 71
- Configuring the T 72
- Configuring the Users 73
- Settings 73
- 74 74
- OSD Functions 75
- Scanning 76
- Computers (F4) 76
- Tuning (F5) 76
- Moving the Label ( F6) 77
- 78 78
- Starting and C 80
- Software 80
- Verifying the V 81
- RICC/ROC Version 82
- Obtaining N 83
- Firmware 83
- Troubleshooting 84
- – Update Software 84
- 6.4.4 Electricity F 85
- 86 86
- 7 Technical Specifications 87
- Technical Specifications 88
- 88 88
- User Guide 89
- 9 SNMP Events Table 90
- SNMP Events Table 91
- User Guide 91
- 201204210 • 933213_EN 92
Manuais e produtos relacionados com Redes Minicom Advanced Systems Smart 4
(92 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais