Minicom Advanced Systems DX System Guia do Utilizador

www.minicom.com International HQ Jerusalem, Israel Tel: + 972 2 535 9666 [email protected] North American HQ Linden, NJ, USA Tel: + 1 908 486 2

DX POWER SWITCH 8 PORT 9 5. Press the TAB key. The Configuration menu appears and the DX Power Switch-Standalone is in Configuration mode. Follow the

USER GUIDE 10 Network Parameters Settings Menu Command /NP This menu is used to configure all Network parameters (IP Address, Subnet Mask, Gateway and

DX POWER SWITCH 8 PORT 11 Command 4 NETWORK PARAMETERS SETTINGS Port is: 80 Enter port or <ESC> to exit You must restart the device (Comman

USER GUIDE 12 Command 2 DEVICE 1 / USERS SETTINGS 1. User 1 2. User 2 3. User 3 4. User 4 5. User 5 6. User 6 7. User 7 8. User 8 Enter Sele

DX POWER SWITCH 8 PORT 13 Command 1 GROUP NAME SETTING Group Name is: Device Name Enter Name (max. 32 characters) or <ESC> to exit > C

USER GUIDE 14 3. Device #2 Activated Twin Mode 4. Device #3 Not Activated Single Mode 5. Device #4 Not Activated Single Mode

DX POWER SWITCH 8 PORT 15 SOCKET RESTART DELAY SETTINGS 1. Delay before Restart (sec) 5 Enter Selection or <ESC> to exit > Command 1

USER GUIDE 16 Command 1 IP SECURITY SETTINGS Mask #1 0.0.0.0 Deny Not Activated 1. Edit the Mask 2. Permit / Deny 3. Activa

DX POWER SWITCH 8 PORT 17 RESTART THE DEVICE The system is reinitializing, please wait ... > 9. Security parameters configuration Masks settings

USER GUIDE 18 Example 3 Permit access to IP addresses beginning with 192 only Deny access to IP address 192.168.001.010 Mask IP Address Permit Deny

DX POWER SWITCH 8 PORT 1 Table of Contents 1. Welcome...

DX POWER SWITCH 8 PORT 19 Use any other straight Serial cable. For EMC reasons, we advise not to use cables above 2.9 meters long. DX Power Switch-Sl

USER GUIDE 20 Figure 5 Password box Type a user name and password. With the administrator name (default admin) and the administrator password (defau

DX POWER SWITCH 8 PORT 21 Default Configuration of the DX Power Switch-Standalone IP address 192.168.100.100 Administrator Name: admin Subnet mask 255

USER GUIDE 22 Example to control the Standalone: P10=1 Enter switch all 8 sockets ON P10=0 Enter switch all 8 sockets OFF P14=r Enter restart s

DX POWER SWITCH 8 PORT 23 9.600 bauds, 8 bits, no parity, 1 stop bit and no flow control. If you use the MicroTerminal program on the CD you only hav

USER GUIDE 24 14. Technical specifications DX Power Switch-Standalone Network standards IEEE 802.3, 10BASE-T Network protocols TCP/IP, HTTP, UDP Net

DX POWER SWITCH 8 PORT 25 DX Power Switch-8 port Serial connection RS232, SUB-D 9 female Nominal input voltage 230 V/50Hz Input power socket IEC-

USER GUIDE 26 Regional Offices Germany Kiel Tel: + 49 431 668 7933 [email protected] France Vincennes Tel: + 33 1 49 57 00 00 info.france@min

USER GUIDE 2 1. Welcome The DX Power Switch 8 Port system is produced by Minicom Advanced Systems Limited. Technical precautions This equipment gener

DX POWER SWITCH 8 PORT 3 2. Introduction The DX Power Switch 8 Port from Minicom is a power management system consisting of 2 units. The DX Power Swit

USER GUIDE 4 The DX Power Switch devices can only be connected to three-wire 230 VAC (50-60Hz) sockets. Always plug the DX Power Switch devices into p

DX POWER SWITCH 8 PORT 5 6. Assigning ID numbers Assign an ID number to each Slave by positioning the dipswitches marked Slct on the front panel accor

USER GUIDE 6 Note! The DX Finder Utility uses the UDP protocol. This program does not work if the administrator has deactivated it in the configuratio

DX POWER SWITCH 8 PORT 7 Configure the Network parameters. The default Network parameters are as follows: IP address 192.168.100.100 Subnet mask 25

USER GUIDE 8 Security Tab Type addresses which are authorized or denied access to the DX Power Switch over the Network. For details about these featur